Monday, October 27, 2008

Acetate Treat Holder Tutorial

Hi! I know this is going to have a post date other than today's date. That's because I had it ready to post a few days ago and completely forgot to do so. It's just been one really crazy week. From my chats with a lot of you, it sounds like it has been this way for most. Well, I hope everyone is hanging in there! Maybe next week will slow down for us a little? lol!

Anyways, here's what I was supposed to post earlier this week. Enjoy!

This box is the one that was created by Susie McCormick called "2,4,6,8 Acetate Box".

I didn't want to just take all the hard work she put, into creating her Adobe file, that she had shared with demonstrators at SCS, and post it publicly here. So I have put together a little step by step pictorial for all of you. Thanks, Susie, for sharing the file with us fellow demonstrators!



You will need 2 sheets of your favorite DSP (designer sheet paper) - 2-1/2" x 8-1/2"



With each sheet of DSP, you will score at: 2", 4", 6", 8" along the strip

Photobucket



Turn the DSP on its side and score it at a 1/2"

Photobucket



Trim 1/2" off the end but leave the short tab attached up on top

Photobucket



Photobucket



Cut each 2" scored line up to the 1/2" mark

Photobucket



Shuffle the cut slabs until it is a snug fit. I like to lift each one in order and glue each layer down.

Photobucket



Photobucket



Glue down the tiny tab inside the box.

Photobucket



Repeat this with second DSP. You need one for the top of the treat holder and another for the bottom.



Trim your acetate (transparencies) to 3-1/2" x 8-1/4"

Score at 1-15/16" four times across the sheet.

You will have a 1/2" tab left at the end.



Photobucket



Photobucket



Crease all folds. Add adhesive along the outside of the 1/2" tab.

Photobucket



Photobucket



Add adhesive to the "bottom lid" and slip in one side of the acetate box.
Press all sides firmly against the sides.

Photobucket


This is what it looks like now with the top lid on and a bit of yummy inside:

Photobucket

Now for the holes on the side for the ribbons. Find the seam of the acetate. This is the "back" of your box. The 2 holes you will make will go to the sides of this seam. Use your hole punch to get in under the "top" lid. Punch a hole on each side.

Photobucket

Put the "top" lid back on. Using a small tipped marker, make a mark where your holes are on the acetate. Take the lid off and use the same hole punch to go over the marks you made on each side.

Photobucket

Thread ribbon in through the holes of the acetate first, then out through the holes of the "top" lid. Place the lid back on the box and tie a knot at the end of the ribbon.

Photobucket

Photobucket

I hope you have enjoyed this tutorial and find it easy to use. Please give proper credit to Susie McCormick for the original design of this most adorable treat holder when you pass it on.

Happy Hauntings!

Jane






7 comments:

~amy~ said...

WOW! thanks for the great tut! Such a cute treat holder Jane!

StinkerbellSteph said...

Super cute box and great tutorial!!

Carla said...

This is really wonderful, Jane!! Great project!!

AnneMarie said...

so wish I had seen this before...
what ever happened to SBS 11??? I have not stamped in a while... new baby and all...
our group fell apart and never made challenges... now I see a lot have dropped off??

love your blog!

Carolina said...

Love it - awesome tutorial too!

Sadie said...

This is a fantastic project, you make it look so easy.
I have loved visiting your site you have some wonderful items, thank you for popping by my blog & wishing me a happy birthday & for your lovely comments.

Teri said...

I can't wait to try out this box. Always wanted to make one of these. TFS this great tutorial! xo, Teri